CNC
What software do I install to operate my CNC Machine?
You install CNCbase to operate a physical CNC Machine, while CNCMotion will run a machine it requires licensing and must be purchased separate. CNCMotion can also introduce errors if the location of the vise/part is not perfectly matched between the ...
How do I get the Educational Version of V-Carve Pro?
After you purchase a CNC Router / Plasma cutter bundle from Intelitek a common question is, "How do I get the educational license for the V-Carve Pro Software?" The machine will have a USB Drive included with it. On the drive will be a text file with ...
How do I enable/disable my CNC Accessories?
This article assumes your accessory is physically installed into your CNC, if that is not the case please refer to your accessories installation guide. Have a CNC accessory that you're unable to use because its icons are missing after a fresh install ...
How do I use my Handwheel / Jog Pendant on my CNC
Setting up the Handwheel for the Bench / Pro Series of CNC Machines Connecting the Handwheel Turn off the machine. Remove the plastic cap. Align the key between the connections. Tighten the connection, by turning the collar. Configure CNCBase Goto ...
How Do I Setup the Tool Library on my CNC Machine
DEFINING THE TOOL With exception of the Current Z and Diameter Offset the settings in the tool libbrary are only used for the Verify window. 1. Click Tools | Setup Library in the Main Menu. The Setup Tool Library window is displayed. 2. Select Tool ...
My Spindle will not Accept / Release Tool - ISO20 Tooling
If you have trouble installing or removing a tool check the following items as they may be the cause of the issue. Pressure Into the Machine is too low. 1. Open the left rear door on the machine. It will probably be locked, the keys should be in the ...
CNCBase or CNCMotion : Waiting for Spindle to Start
You receive the message Waiting for Spindle to Start. This error can happen using a machine On-Line or in Simulation This is caused by one of a few technical problems with the PC and Control Software. The Bench/Pro machines doe not use a spindle ...
BAD Arc while running G-Code
Warning.... Bad Arc. - Press F5 to Continue If you receive the above message that means the Control Software is unable to compute the Arc it being asked to cut. The issue is usually caused by a math error by the user or CAM software creating an ...
What Oils Do I use on my BenchMill, ProMill, BenchTurn, ProTurn CNC Machines
Intelitek recommends using a ISO Viscosity Grade 46 Hydraulic Oil in the manual one-shot oiler. The machines one-shot handle should pulled once per day of operation. Mobile Oil Part Number: 100814 (1 Gallon) Mobile Oil Part Number: 122977 (1 Quart) ...
CNCMotion is asking for a CD-Key to run my CNC Machine. Where do I get a key?
CNC Motion is simulation software. It is extremely common for users to get confused by the "Motion" name and think that should run their CNC machine. The correct software to run the CNC Machine is CNCBase. This software is part of the same ...
Machine is Losing Z Position Changing Tools, Between Reboots, or Changing Users
If you are using CNCMotion to control your machine, we recommend you switch to CNCBase. If you wish to continue using CNC Motion then note that the tool library is saved per user and not per PC. Setting Up the ATC or Manual Multi Tool Change 1. Home ...
Where can I find the Post Processor for my CNC Machine
We do have a single exception, we do have a Fusion 360/HSM for the ProTurn/BenchTurn Lathe. Link Intelitek does not create or keep post processors for various software packages, though most vendors do have some version of a Post Processor that works ...
My Bench / Pro CNC Machine won't connect to my PC. Machine wont move. Error Initializing Control
My Bench / Pro CNC machine won't connect to my PC. My machine won't move. I get a message, "Error Initializing Control" If for any reason you change computers, during this process you need to turn the machine off and on again. The machine will only ...
Where do I find the software for my older CNC Machine?
The software for the xxxxx_Light and Benchman CNC Machine is located at https://downloads.intelitek.com/. 1. Click Download Software 2. Click CNC Machining 3, Click Discontinued CNC Software 4. Find your machine and download the appropriate software. ...